Wednesday, April 29, 2009
Teknik foto pemandangan (landscape)
Teknis Fotografi & Fungsinya
Namun, sepertinya mustahil dapat menghasilkan foto seperti itu jika tidak mengenal dan memahami dari masing-masing teknis fotografi dasar. Fotografi memang bukan segalanya tentang kamera, namun kamera adalah alat untuk menyalurkan visi kita itu. Maka, sekiranya perlu mengenal dan memahami bagaimana kamera bekerja.
Tugas utama dari kamera adalah mengatur intensitas cahaya yang masuk dan pada akhirnya mengenai film/sensor (selanjutnya saya sebut medium). Apabila, kamera mengizinkan terlalu banyak cahaya yang masuk maka medium akan terbakar (overexposed). Dan sebaliknya. Bagaimana agar cahaya yang masuk itu tidak berlebih dan tidak kurang, atau dengan kata lain ‘pas’. Berikut saya jabarkan satu-satu.
Aperture
Atau yang sering juga disebut dengan difragma atau bukaan lensa adalah berfungsi untuk mengatur seberapa besar lensa akan terbuka. Fungsi ini lebih tepatnya terletak pada lensa. Logikanya, semakin besar bukaannya, maka akan semakin banyak cahaya yang akan masuk. Seperti sebuah kran air. Semakin besar kita buka keran tersebut maka akan semakin banyak air yang akan keluar.
Penulisan Aperture yang benar adalah f/x. Sehingga apabila dikatakan nilai Aperture-nya adalah 5.6, maka penulisan yang benar adalah f/5.6. Jadi jangan bingung apabila ada yang bilang bahwa bukaan lensa 2.8 lebih besar dari bukaan lensa 5.6. Karena kalau secara penulisan matematisnya memang benar khan? (f/2.8>f/5.6) Tapi kebanyakan kita malas untuk bilang f/2.8 atau f/5.6, karena kita orangnya simpel sih…
Efek Samping dari Aperture
Seperti obat batuk yang memiliki efek samping, begitu juga dengan aperture. Efek sampingnya adalah semakin besar bukaan lensa, maka akan semakin kecil daerah fokusnya. Dan sebaliknya. Daerah fokus inilah yang biasa dikenal dengan DOF (Depth of Field).
Shutter Speed
Atau yang biasa disebut juga dengan speed atau kecepatan rana bertugas untuk mengatur berapa lama mirror terbuka lalu menutup kembali untuk membatasi berapa banyak cahaya yang akan masuk. Seperti teori keran, apabila kita membuka keran terlalu lama, maka wadah penampung air tadi akan kelebihan sehingga akan meleber keluar. Kalau dalam kasus fotografi, medium akan terbakar.
Penulisan shutter speed yang benar adalah 1/x. Sehingga apabila dikatakan bahwa sebuah foto menggunkanan speed 60, maka penulisannya yang benar adalah 1/60 detik. Jadi jangan bingung kalau dikatakan bahwa speed 60 lebih cepat dibandingkan 30. karena secara penulisan matematis memang begitu khan?
Efek Samping dari Shutter Speed
Seperti berpacaran yang memiliki efek samping, seperti sulit melirik wanita/pria lain, begitu juga dengan shutter speed. Semakin cepat shutter speed, maka akan gambar akan semakin terlihat diam (freeze). Dan sebaliknya, apabila speed terlalu lamban gambar akan terlihat blur dikarenakan gerakan yang terlalu cepat, sehingga objek terlihat bergerak sangat cepat.
ISO atau ASA
Adalah tingkat sensitifitas medium dalam menerima cahaya. Semakin tinggi nilainya, maka akan semakin tingkat sensitifitasnya. Artinya, apabila kita merubah nilai ISO atau ASA ini menjadi lebih tinggi, sedangkan aperture dan speednya tidak diubah, maka medium akan menerima cahaya lebih banyak. Dan sebaliknya.
Efek Samping ISO atau ASA
ISO adalah tingkat sensitifitas sensor (medium), sedangkan ASA adalah tingkat sensitifitas film (medium), jadi perbedaannya hanya dimediumnya saja. Tapi logikanya sama. Kecuali efek sampingnya. Dimana apabila menggunakan film ASA tinggi, maka gambar akan terlihat grainy (berbentuk titik kecil namun banyak). Sedangkan penggunaan ISO tinggi akan menghasilkan noise (seperti bentuk cacing namun banyak).
Thursday, April 9, 2009
All About Batteries
TERMINOLOGY
Battery versus a cell: Most people use these words the same way. Battery engineers only use "battery" to refer to two or more individual cells connected together within one package. Thus your watch probably only has a single cell, your flashlight has a couple of cells, and your camcorder has a complex battery with several cells inside the black plastic package. No big deal.
Throw Away or Rechargeable: Engineers call throw-aways "primary," and rechargeables "secondary."
Power is expressed in Watts. Multiply current, measured in Amperes (Amps), by Volts to get power in Watts. Power is the ability to do work. If you imagine this as water in a hose, Volts is the water pressure and amps is how many gallons flow. How much you can spray off your driveway is thus the water pressure times how much water flows at that pressure. Volts, Amps and Watts are always capitalized since they are named after men who invented much of this: Alessandro Volta (Italian) who invented the first battery, James Watt (Scottish) who designed improvements to steam engines and mathematician André-Marie Ampère (French).
Energy is power over time, measured in Watt-seconds (Ws), also called a Joule, named after English physicist James Prescott Joule. A kiloWatt-hour is 1,000 x 60 x 60 or 3,600,000 joules. Flashes often measure their power in Ws, for instance, 50 Ws is normal for a shoe-mounted flash and 500 to 2,000 Ws is common for studio strobes.
Capacity is how much current is stored by a cell. Even throw-away cells have these ratings, although only engineers worry about it or look it up. These ratings are plastered all over rechargeables. It's usually measured in Ampere-Hours or milliAmpere-Hours. 1 Ah is the same as 1,000 mAh. A 1,000 mAh cell can deliver 1,000 mA for an hour, or 1 mA for 1,000 hours.
In reality cells are measured at about a 20 hour discharge rate. Cells have less capacity when more power is drawn, thus a 1,000 mAh cell would probably die after a half hour if delivering 1,000 mA. When capacity is measured it is measured to a stated cut-of voltage and at a stated rate. The same cell will have completely different capacities when measured at different rates and to different cutoff voltages. Therefore when you see these numbers on a package they are meaningless unless the rate and cutoff are specified, which usually they aren't. In addition to plain lying, this explains why you shouldn't bother to compare different brand's ratings to each other.
Throw-Away (Primary)
"Heavy Duty"
Avoid these. They are also called carbon zinc, zinc-manganese dioxide, Zn/MnO2, and LeClanché. These are the oldest, crummiest kind. Remember when flashlights only worked for a few minutes before they started to get dim? These were the batteries! They never could deliver much power for anything. You can still get these throughout the third world and in discount stores. I was amused at seeing a Duracell ad poking fun of the Eveready brand of these. It was unfair since Eveready makes both these crappy kind as well as batteries far more advanced. Anyway, ignore these batteries for everything except things with very low drains. Don't use them for a flash. They work great in things that run for a year like smoke detectors and clocks. They die after a couple of years in storage.
Capacity: Eveready Heavy Duty AA: 1,100 mAh.
Alkaline
These are the most popular today and work great. There are some premium versions, like Eveready's e2 Titanium, that work a little better in high-power applications like flashes and digital cameras. Personally I find they cost more than the benefit they offer compared to the regular alkaline batteries. Alkalines come in every size, from regular AA, C and D sizes as well as little button cells for watches and light meters. They last for years in storage. I have a healthy set in a flashlight that still works great even though the install by date passed five years ago.
Capacity, AA size: 2,700 to 3,135 mAh. Most AA Alkaline cells offer a capacity of 2,850 mAh. The expensive Energizer e2 alkaline offer 3,135 mAh and the cheapest cells offer 2,700 mAh, all pretty much alike at low drains. That's why Consumer Report's testing suggested to get whatever's cheapest. Note that "Titanium" is just marketing poof; these are not Lithium or titanium, they're just alkaline.
Because Duracell, Eveready Energizer and Rayovac offer to repair any damage caused by leaking batteries I only buy them, and never store brands. Even though the discount brands offer the same performance for a lot less money, when you eventually have one leak in your camera you'll be very, very glad that you weren't using store brand alkalines! I had a flash damaged once, and the battery company actually sent me a new one! One device damaged but saved by a warranty easily pays for the extra cost.
anasonic Oxyride
Panasonic introduced these in 2005. I have not tried them yet. They sell for the same price as alkaline AA cells. They have a higher initial voltage, 1.7V, compared to ordinary alkalines which are 1.5V. Thus when new flashlights will burn brighter with Oxyride than with other cells. This also means that the bulbs will burn out faster, too.
David Pogue in the NY Times on April 7th, 2005 did the best article I've read on the Oxyrides. You may be able to read it here if you're signed up with the NY Times.
David found that for high-drain applications, specifically in a digital camera, that indeed they lasted for 844 shots compared to 566 for premium alkalines and 354 shots for regular alkalines. GREAT!!!, and at the same price as regular alkalines.
On the other hand David found that the Oxyrides lasted less long than alkalines for low drains. They lasted about as long as alkalines when discharged at a four hour rate. Oxyrides were worse than alkalines at lower drains like a 10 hour rate.
Thus from David's observations Oxyrides are fantastic for high drains like digital cameras and I would suggest them also for electronic flash, but a poor choice for clocks, pagers and radios and things that usually run a long time on a set. For these regular alkaline are still better.
Lithium (note that Lithium also comes as Lithium Ion rechargeables below)
These are expensive. They were developed for the US military because they offer double the power in the same size with half the weight. This is important when you have to carry a month's worth of batteries for your night vision system in your pack. Today these are the batteries that run your camera and cost $10.
Hint: Camera stores make a lot of money selling batteries. Look around online to get much better deals than retail. Lithium batteries have shelf lives of ten years or more, so stock up and don't worry. They come in various special sizes for cameras and also AA. You have no choice for the special camera sizes; they only come in Lithium. You have many choices in AA size, here are some tips.
Capacity: Energizer Lithium AA cells offer 3,000 mAh, the same as Alkaline.
Tip: Use the AA lithiums only for things that draw a lot of power, like a flash or a digital camera. They offer the same life as alkaline in things like clocks and pagers. They offer greater life only when you draw a lot of power as in a digital camera or flash. Otherwise they cost $10 for a set of four compared to 99 cents or less for alkaline. I have never found the lithium AAs for less than about $2 a cell, let me know if you do. Amazon has them for $2.50 each, a pretty good price, here.
Tip: I have not confirmed what the data sheets say personally, however if it ever got as cold as freezing here in California I'd point out that Lithiums are supposed to work better than alkalines at cold (sub-zero) temperatures.
Tip: AA Lithium can't deliver much instantaneous power as other technologies. Thus you get the slowest recycling times in flashes. The lithium cells are designed this way because otherwise the lithium chemistry is so potent it would tend to heat up and explode. You'll get faster flash recycling with rechargeables or even regular alkalines. You will get twice as many flashes with the lithium, just not as fast recycling. This is a minor point. If I had someone else paying for my batteries I'd use lithium AA for everything.
Tip: I've gotten some bargains at as-seen.bizhosting.com and www.batterystation.com. Also ContinentalPhoto.com is suggested by a reader as having great deals on these.
Idea: There is a rechargeable CR-V3 system I've seen circulating under various sub-prime brand names. You can get one here for $30 with the charger and spare batteries here for $20. I've seen claims of these replacing two AA cells in addition to the throw away CR-V3. These only have a capacity of about 1,300 mAh, less than half of a throw away CR-V3 (2,900 mAh) and less than Ni-MH rechargeable AAs (typically 2,300 mAh today). I also see claims of it outrunning Ni-MH, so try it yourself. I'm a cheapskate so I refuse to own anything that uses throw-away $15 batteries, so I have not tried this system. If I used these batteries I'd order one today since as soon as you use it a couple of times you're already ahead.
Mercury (obsolete)
Mercury cells are no longer available in the USA. They were used in cameras from the 1960s and 1970s. Mercury cells had the advantage of constant voltage all the time, so they were ideal as references powering CdS cell light meters.
There's more here on them.
I have had my Luna Pro meter updated to run on ordinary S76 cells and it works great.
Rechargeables (Secondary)
Lead Acid and Gel Cells
The first lead-acid batteries were used for telegraphy by Gaston Planté in 1859 and became available commercially in the 1880s. It's interesting to note how rechargeable batteries have always been involved with communication; your cell phone today runs on a Lithium Ion battery described below. A lead-acid battery starts your car. They are filled with liquid sulphuric acid and you don't want to spill them. Lead acid batteries are also available with gelled acid, called gel cells, which doesn't spill and can be used upside down. Gel cells are used in home alarm systems, backup power systems and your home computer's uninterruptible power supply (UPS) if you have one. Lead acid is not used in photography, except as heavy duty supplies for some lighting equipment.
Care and Use: Lead acid batteries prefer to be kept charged all the time. They can deliver very high power. That's why they are perfect for use in your car: they can deliver thousands of watts to start your car, and then are kept charged as you drive around. Deep cycling them is bad for them, and there are special kinds of lead acid batteries designed for this. Likewise, they are perfect for use in power backup systems where they are very happy being kept charged for years just waiting and can deliver enormous amounts of power instantly. Most television networks each have a room full of lead acid batteries that are always kept charged. If the power goes out these batteries can deliver enough power to run the entire network headquarters for 10 minutes or so if they have to if the Diesel generator doesn't start immediately. Other kinds of battery need exercise; lead acid doesn't.
Charging: Lead acid is very easy to charge. They are charged to a constant voltage through some form of current limiter.
Alkaline: Ray-o-Vac invented rechargeable alkalines in the 1990s. They never caught on.
Nickel-Cadmium (Ni-Cd)
These were the first popular rechargeables for modern electronics. They got popular in the 1960s. They still offer the most charge and recharge cycles of any technology. They also offer the lowest capacity so you'll be charging them much more often. Ni-Cds are unbeaten in their ability to provide dangerous amounts of current instantaneously if short circuited. Therefore they're popular in cordless soldering irons because they heat up instantly. Caution: if you short circuit them with a wire the wire will immediately glow and maybe even burn up. You easily can hurt yourself if you throw them in a pocket with keys or change. This of course is a good thing allowing fast flash recycle times and fast frame rates when used in camera motor drives.
Capacity, AA size: 650 to 1,000 mAh, not very much.
Care and Use: Mandatory: they should always be fully charged and then run all the way down before being charged again. This means for most field uses you need two sets so you have a fresh set with you for when the first set dies. If instead you just charge them up when you need them you eventually will get very little run time. This is called the memory effect. They learn how little you use them and then only provide that much capacity. They're like muscles: you have to use them to keep them strong. You have to baby Ni-Cds so I don't recommend them for anything. They also contain poisonous cadmium and must be disposed of properly. I don't even know where you can buy these today.
Charging: At slow overnight rates even the simplest circuitry has been used to charge Ni-Cds, since you don't have to worry about them overcharging at the slow rate. More advanced circuitry is required to charge them more quickly since the Ni-Cds could blow up at faster charge rates if the charger is not smart enough to cut off the current. Smart chargers today are very common and can charge these in several hours or less. As soon as all the charge is put back you stop charging, simple.
Nickel-Metal Hydride (Ni-MH)
These are the most popular rechargeables today in AA and other regular sizes. They replaced Ni-Cds in notebook computers in the late 1980s and became available in AA size in the 1990s. They offer twice the capacity of Ni-Cds and require less babying. Most chargers recharge them in a couple of hours. Otherwise they are very similar to Ni-Cd, although don't have quite the peak current ability of the Ni-Cds or offer quite as many charge/discharge cycles.
Charging Speed
The electrical energy fed to a cell turns to chemical energy as it charges. When the cell is full the power no longer can turn to chemical energy and instead turns to heat. If the charger isn't smart enough to know when to turn off, which was the case in the 1970s, the charging current needed to be low enough not to damage the cell from overheating. This is why it took 15 hours to charge Ni-Cd cells back then, and why the crummiest chargers still take overnight.
The speed of any charging system today is limited its ability to know when to turn off. If you continue to jam a lot of power into a charged cell it will explode; whoops! Today most Ni-MH and Ni-Cd systems take a few hours. They measure when the cells are full based on voltage fluctuations (they look for a slight dip in voltage signaling a full Ni-MH cell ) and / or the temperature rise that signals the end of charge. The cells are supposed to get hot at the end of charging; that's one way the charger detects when to turn off.
Regular three hour chargers are smart, but since they usually don't monitor each individual cell they still have to be careful since all cells aren't charged at exactly the same time. The first cell to finish charging still has power jammed into it while the other three cells finish up. This limits what's safe.
Rayovac has a unique system that charges their special Ni-MH cells in 15 minutes. They use charging control not just in the charger, but also use chips in each individual cell. This way there is no danger of one cell exploding while the other cells are still charging. With Rayovac's chips in each cell the charger jams in current like there's no tomorrow and each cell shuts off exactly when it needs to. From what I hear these really work well!
Capacity in AA size: 1,350 to 2,500 mAh. Look out, many shifty brands lie about their capacity. 2,300 is pretty standard in 2004 and 1,350 was typical in 1999. My 1999 1450 mAh Sanyos still outperform newer off brands marked 2300 MAH! in big letters, so buy quality and not specs. Anything from battery pioneers GE/Sanyo and Panasonic ought to be great.
Care and Use: They still should be completely run down and then fully charged each time. They give the best service and life this way. Avoid using Ni-MH if you don't intend to run them all the way down each time. I always have two sets with me, so I can replace the set in use when it runs down completely. The advantage of Ni-MH over Ni-Cd is that if they lose capacity from memory issues you easily can rejuvenate them by running them through a full discharge-charge cycle a couple of times. They do have memory issues, which is why you see so many sold as "memory free." Baloney; the problem just goes away easily by fully cycling them. Unlike Ni-Cd, I've gotten great service from every Ni-MH system I've used by always fully cycling it. I've got many more years of service from an old cell phone that used these batteries than the phone service facility could believe, and the Ni-MH AAs I bought 5 years ago still work as well in my flashes and cameras as when I bought them.
Where to get them
I have one of these great systems here. It's great for travel with its small size, a folding built-in plug, needs no cord or external power adaptor and runs on any power worldwide from 100 - 240 V and 50 - 60 Hz. All you need to use it anywhere from Japan to Iraq are a few passive plug adaptors.
Some people, especially amateur radio operators who have been using these things in their walkie talkies for years, love the Maha systems like this one here.
I also have one of these LaCrosse chargers, the best to get for home since it also measures capacity, recycles and even can rejuvenate cells.
If size isn't important, today I'd first try the brilliant new Rayovac 15 minute system mentioned above. You can get the charger here and the cells here. I'm unsure if the charger includes cells or not and I'm also unsure just how many cells come with the cells ordered alone at those links. It's much more powerful to charge so quickly and therefore is big, heavy, has a fan in it and doesn't run worldwide.
Caveat: 5 years ago Ni-MH was an advanced technology, so the only manufacturers who made them, like Sanyo, made them well. Today all sorts of garbage is out there, and on top of that many makers make bogus claims about capacity (mAh). My 5 year old Sanyos, rated at 1,350 mAh, still give me more service than another brand I was given with "2,300 mAh!!" printed in huge letters. Next time I buy I'll get anything made by Sanyo (who also has made them for Kodak and GE) or Panasonic and possibly Sony. I'd pass on anything lacking the name of a real company on them.
Charging: Ni-MH chargers are usually smart chargers which measure voltage and temperature to stop charging as soon as the batteries are full. Thus they can charge batteries as quickly as an hour or less since there is no worry about overcharging at the fat rate due to the smart charger. As soon as all the charge is put back you stop charging, simple.
Lithium Ion
These are the newest and best rechargeables, since they offer the most power, the smallest size, the lowest weight and require no babying like the Ni-MH and Ni-Cd. They are also the most complex and expensive. They were introduced in laptop computers about 1994 and became common in camcorders and everywhere in the late 1990s. They removed many pounds from each laptop and doubled the run time almost overnight. We would have no iPods or tiny cell phones and microscopic digital cameras today without these. Today every camcorder or digital camera and laptop computer uses these. They only come in special sizes designed specifically for a given piece of equipment and typically cost $30 - 100 to replace.
Care and Use: Completely different from Ni-Cd and Ni-MH, lithiums prefer to be charged early and often. They don't like to be run all the way down. You will get only a few hundred cycles if you run them all the way down each time, and thousands if you charge them up while still mostly full. Lithium Ion's life tends to be measured by how much total energy comes in and out of the battery and not by cycles. Actually you can get more total energy from the battery by only partly using the battery's capacity. Thus I always charge every Lithium Ion battery every night when I've used it the day before, completely unlike the other technology cells. I've gotten great service out of every one I own; I charge my cell phone daily and I've been using it for years.
Chargers: They require very special chargers, unlike Ni-Cd and Ni-MH. Lithium is charged at a fast rate to replace the majority of the charge, and then trickle charged to replace the last 25% or so. Thus you may see charge state indicators which let you know when they are almost done, which happens very fast, and completely done, which takes much longer. Because special charging circuitry is required they are not offered in sizes to replace regular AA or other batteries, since people like me would goof once and blow them up in the wrong charger. Also they don't come in the special 1.5V versions invented by Eveready as a disposable cell, so today you can't get the rechargeable lithiums in AA size.
Brands: Li-Ion batteries require complex charging circuitry and sensors. There are many cheap counterfeit copies out there which skip some safety features. These phonies can and do explode! Because of this I would never buy any non-original brand rechargeable battery to replace any of the specialized batteries in my cameras and computers. Sometimes even legitimate suppliers get stuck with bad parts. See the Nikon recall for instance.
More Li-Ion technical info see Powerpulse and Cardex and here, too.
USE IN ELECTRONIC FLASH
Most applications have a clear winner for what sort of battery is best. Only in some applications, like AA size, do we have so many choices. Here are some comparisons for use in an electronic flash.
(data from Nikon SB600 instructions, typical for most flashes)
Recycle Time (fresh batteries) | # of Full-Power Flashes | |
Ni-MH | 2.5 s | 220 |
Alkaline | 3.5 s | 200 |
Lithium | 4.0 s | 400 |
Ni-CD | 2.9 s | 90 |
Thus I use Ni-MH. If you don't shoot as much use alkaline. If someone else is paying and you're going overseas by all means just pack a bunch of lithiums.
Ni-MH give shorter recycle times even though they have less mAh than alkaline because Ni-MH have much lower internal impedance. That means they can crank out a lot more amps intermittently than alkalines. Flash uses huge amounts of current for just a few seconds to recycle, thus the Ni-MH can belt it out faster than alkalines. Alkalines are not very happy having to spit out a lot of current all at once, which is what flash needs, unlike a radio. Alkalines don't recycle as fast, but will last for years sitting in an unused flash, while Ni-MH will go dead just sitting there after a couple of months.
RECYCLING
All modern batteries are loaded with powerful, poisonous chemicals and metals.
Actually except for the old carbon-zinc, you ought to recycle every dead battery.
This is easy in the USA. As I recall Radio Shack takes all batteries for recycling, and with more Radio Shacks in the USA than McDonalds (no kidding) it's not hard to find them.
Source : http://www.kenrockwell.com
The Zone System
INTRODUCTION
Zones are levels of light and dark.
A Zone System is a system by which you understand and control every level of light and dark to your best advantage. It works in digital just as it does for sheet film. Having a system allows you to understand and be in control, instead of taking whatever you get. Ansel Adams was asked in the 1950s if he thought the Zone System was still relevant in that then-modern world. He replied "If you don't use the Zone System, then what system will you use to know what you've got as you photograph?"
There are many ways to evaluate what you'll get in your final print or display as you photograph. The Zone System is one way to get a handle on everything. When you know what you're going to get you can make changes as you're photographing to optimize your final prints.
The Zone System applies as much to color, digital and video as it does to black-and-white. Ansel Adams even shows us in The Negative how to use it with point and shoot cameras!
Ansel Adams chose to divide the range between white and black into about ten zones. Each is an f/stop apart. Color film and digital tend to have fewer zones, but that's not important. What's important is understanding how these zones relate to one another and how they change as they go through each step of any photographic process.
From the 1920 through the 1960s The Zone System usually required weird film developing, since people developed sheet film one shot at a time and printed on fixed-contrast papers. It was a pain.
In the 1970s through today the Zone System for film became more involved with printing as people tended to shoot rolls of film that are developed all at once and print on variable contrast paper.
With digital in the 2000s the Zone System focuses more on understanding how digital cameras respond to different levels of light and dark. The Zone System is the basis of understanding PhotoShop's Curves command. With digital cameras you set contrast in-camera, or do as I do and let the camera do this automatically.
The biggest advantage of understanding a Zone System is understanding what's going on. You'll be able to concentrate on making great images instead of worrying about petty things like technique and exposure.
Digital cameras no longer require spot meters. Spot meters were used to evaluate subjects before they were photographed. It was the only way we had to predict exactly how to expose, develop and print before we made an exposure on film. Today we have histograms and LCDs instead. Today I use a digital camera instead of a spot meter to evaluate this better than a spot meter for my view camera!
That said, let me offer that the rest of this page was written in 1999 when I wrote it to apply to color slides.
The Zone System allows you to get the right exposure every time without guessing. It does not require you do any special film development and you never have to waste time with bracketing. Now aren't you interested?
The Zone System is very important to understand, especially for color slides.
Today the Zone System is the careful and analytical setting of exposure. Almost no one does special development for each negative any more.
I learned it all from Ansel Adams' book "The Negative." He covers the Zone System for use with color film and point-and-shoot cameras, too.
Ansel worked in the days when everyone shot sheet film developed individually by hand, and when the only decent papers were fixed contrast.
Therefore of course he suggested screwing with the development of each sheet to print on grade 2.
Today most people shoot color or roll film and variable contrast papers are among the best papers available. Therefore custom development of each image just isn't happening! Today we usually use standard development and vary contrast in printing.
Even Ilford recommends today what I do for color and B/W negatives: ensure you get enough exposure in your shadows, develop your film normally, and then use variable contrast paper for your prints if you need to.
For color one always uses standard development. The colors get very screwed up of you try to vary development times. I have tried with Velvia and guess what: the overall contrast remains almost unchanged with even a plus or minus two stop push or pull! The DMax and shadow level changed, but the contrast of the active image was about the same. Worse, the color balance goes a nasty cyan with a pull. Color takes on a nice warmth with a push, although I only push when I need speed.
Here are my quick suggestions:
METERS much more here
If you are shooting a modern SLR, use your built in meter in Matrix (Nikon) or evaluative (Canon) and forget about most of this. You will need to know when to compensate you meter a bit, but otherwise all Matrix and evaluative systems incorporate the Zone System automatically.
I have a page on how to use the Nikon built-in spot meters here.
If I am shooting a camera with no meter, I use the same meters Ansel did, and you can still buy them today. I use either the Pentax Spotmeter V (analog) or Pentax Digital spotmeters. The digital one is smaller and I use it today as Ansel did at the end. The analog model is more precise and easier to read and interpret, however it is bigger and more delicate. The Pentax meters are superior to the complex, confusing and more expensive Gossen and Sekonic models.
COLOR NEGATIVES
For the color negatives shot by most amateurs just set the camera on automatic and GO! The films today have so much latitude that you just can forget it. Honest, I have tried shooting the same scene at normal and FIVE STOPS overexposed on Fuji 800 and in my prints I can't tell which was which. Never underexpose, that will lead to murky dull shadows. Overexposure by a couple of stops may increase contrast and saturation a little. If color is as important to you as it is to me, unless you print your own work, shoot slides and not prints. See the film page for that info.
B/W NEGATIVES
The same applies as it does for color! Amateurs worry far too much about this. I suggest adding one more stop to your exposure and adding a yellow filter. Try this and be amazed! Details are on my film page starting here.
If you want to get deeper into it, I suggest using your spot meter and setting the darker part of the image to -1 or -2 stops exposure, which is the same as saying Zone IV or Zone III. See more at the bottom of this page, too.
COLOR SLIDES
For now, what you need to know is that if you use anything other than a modern SLR Matrix or evaluative meter, that you need to add or subtract exposure depending on how bright or dark the subject is. Use the spot or center weighted meter and add exposure for light subjects or areas, and subtract for dark ones. SIMPLE!
Here's how much to add or subtract with the center-weight or spot manual meters:
-3 stops (Zone II): Your slide film goes pretty black here. Don't do this unless you want something pretty much completely black. Yes, you can see some detail on Velvia even at -4 stops (Zone I), but good luck trying to print it.
-2 Stops (Zone III): Normal shadows in landscapes are set here. You will use this a lot. This is about as much underexposure you can use and still have detail. For instance, make a spot reading of the shadow and set your camera to underexpose that shadow spot by two stops. If you are lucky everything else will fall into the proper exposure. You don't really need luck: use your spot meter to make sure that at the exposure you set that everything else falls where it ought to per this chart.
-1 Stop (Zone IV): Very few things are set here. This is a dark middle tone, like a red painted barn.
Normal exposure (Zone V): This is where you set middle tones or a gray card. Sometimes the north sky is set to normal (+-0). Oddly, in many scenes there is no middle tone, which is why spot meters usually cannot be used without knowing the zone system. Sometimes green grass falls here.
+1 Stop (Zone VI): Medium light parts of an image. Skin and granite rocks go here. For most landscape photos you'll set your light rocks here, and the shadows at -2 stops. Bright yellow is set at +2/3 stops.
+2 Stops (Zone VII): White things like snow and sheets of white Fome-cor are set here.
+2.7 Stops (Zone VIII): This is where slide film goes clear.
This is how the zones of the classic zone system correspond to the analog bar graph on your exposure meter:
Zone II = -3 stops
Zone III = -2 stops
Zone IV = -1 stop
Zone V = +- 0 stops
Zone VI = +1 stop
Zone VII = +2 stops
Zone VIII = +3 stops
If you are lucky, all the elements in your image will fall within -2 to +2. Usually they won't. Sorry.
If your spot meter tells you that the shadows are darker than -2 stops that simply means they will be fairly black, and if the whites get too much hotter than +2 that they will be completely white or clear.
Slide film usually goes clear at +2.5 stops. It usually starts getting pretty murky at below -2 stops, although you can still see things down to -4 stops on Velvia.
You need to think as a painter does and ask yourself at what level of tone you want each part of your image to render. You need to be in control, and the Zone System lets you be in control. Otherwise you'll simply be gambling that your images will "turn out." With the Zone System you will know when you need to alter your lighting.
Problems
There will be plenty of occasions in nature where God is not putting the light range where you want it. The Zone System is useful here because it tells you before you waste a lot of film that you are probably going to get garbage and thus you can plan or change the light or filtration accordingly.
What do you do if the lightest and darkest parts of the scene are beyond the range of your film, typically +- 2 or 3 stops?
Simple: you have to change the lighting somehow. If you have a very high-contrast scene there is no correct exposure and you will never get what you want.
This is where many amateurs get lost: exposure cannot correct for bad light. OK, nothing can fix bad light. You have to wait for it. Photography takes patience. You can try a graduated Neutral Density filter which often helps bring down an overly bright sky or too dark foreground. Here's an example of one.
Some people try to tweak development to compensate for crummy light. It's much better to fix the light. Ignore the temptation to tweak development; this is why we in Hollywood pull up three trucks of lighting equipment to light a scene outdoors.
If you do your own developing the Zone System gets far more complex if you want to adjust the exposure and development to attempt to fit the range of the scene into the range of the film. This used to be popular in B/W before good variable contrast paper was available, as in Ansel's day. Today B/W shooters make sure that they expose enough for the shadows (make sure everything for which you need detail is exposed at not less than -2 stops) and then use a lower contrast setting for their paper.
If you're asking, no, I have no idea how Ansel got ten zones. Today we only get about seven. OK, actually I do know how he got ten zones: Ansel used less development and slower speeds for his negatives than the manufacturer's ratings. We can't do that with color today. You can do this in B/W, and you have to do a lot of custom testing and developing.
In Ansel's day everyone shot sheet film and used graded paper. Therefore it made sense to develop each sheet differently so it could print on grade 2 paper.
Today people shoot roll film (your Nikon or Mamiya) and need to develop the whole roll the same way. One uses VC (variable contrast) papers to control the contrast, not developing.
You always develop color the same way, unlike B/W. Changing developing times for color often messes up all the color balances.
I have pushed and pulled Velvia and saw little contrast change. The colors shift and the black level changes, but the contrast does not vary as does B/W film.
You have to change the light yourself or wait for God to do it. This is art. Only your heart can tell you what to do. You have to know at what level you want various light and dark areas to render, just as a painter has to decide what colors to take from her palette. There are no written formulae for good photos. Ansel covered this quite well in his books.
Source : http://www.kenrockwell.com
What are LV and EV
LV, Light Value and EV, Exposure Value, are terms used to allow easy discussion of exposure and light without the confusion of the many equivalent combinations shutter speeds and apertures.
LV refers to how bright the subject is. EV is the exposure setting on the camera.
You may have seen them if you like to read the fine print of camera specifications. They are used to specify ranges of light levels for metering and autofocus.
EV and LV follow an open-ended scale. Each one is one stop away from the next. In photography values of about 0 to 18 are commonly used. Negative values are perfectly valid, just very dark and only occur in night photography. LV 15 is full daylight, for example.
Each Exposure Value, or EV, represents any of many different but equivalent combinations of f/stop and shutter speed. For instance, 1/250 at f/8 is EV14, and so is 1/125 at f/11. 1/125 at f/8, one stop more exposure, is EV13, and 1/250 at f/11, one stop less exposure, is EV15. You don't need to remember these, they are on the dial of your exposure meter.
Understanding them will allow you to recognize common lighting values and guess correctly at exposures even without a meter.
This system is the correct way to discuss photographic light and exposure because it avoids all the confusion of f/stops and shutter speeds, if all you really want to discuss is light and exposure levels. it replaces the idiotic question I get all the time while shooting, "what f/stop are you using," which of course means nothing by itself.
LV, or Light Values
An LV, or Light Value, is a number that represents how bright a subject appears in absolute terms. It does not take film speeds or exposure into account. LVs are very handy photographic terms to use to describe lighting levels.
LVs measure light coming from a subject, or "luminance." They are not a measure of how much light is falling on a subject. In other words, the same light falling on a black object will have a lower LV than the same light falling on a white object.
Some light meters, especially spot meters like the wonderful Pentax Digital Spotmeter and analog Pentax Spotmeter V, read directly in LV. You transfer this number to a dial that, along with your film speed, reads out all the combinations of aperture and shutter speed that will give the correct exposure.
Here's a table of common Light Values associated with common situations. If you use one of the Pentax meters you will quickly start to learn these without even needing the meter after a while. This is because the same number pops up for each subject each time. LVs eliminate the confusing issues of film speeds and f/stops that hide these simple truths when using SLRs or other light meters:
LV18 and above: Bright reflection off a sunlit object, including reflections off the sea
LV17 White object in full sunlight
LV16 Light gray object or skin in full sunlight
LV15 Gray card in full sunlight; typical exposure for ugly front-lit noon daylight photos
LV14 Typical light level for side-lit daylight shots in good afternoon light
LV13 Typical shadow cast in a daylight scene; cloudy bright days
LV12 California bright overcast
LV11
LV10 Dark, dreary overcast day in Boston, London or Paris
LV 9
LV 8
LV 7 Typical indoors; light outdoors about 10 minutes after sunset
LV 6
LV 5
LV 4
LV 3 Brightly lit night street scenes
LV 2 Typical night street scenes
LV 1 Dark scenes outdoors at night
LV 0 LV Zero is defined as the light level that requires a 1 second exposure at f/1 with ISO/ASA100 speed film.
LV-1
LV-2
LV-3
LV-4
LV-5 Scene lit by the full moon
LV-15 Scene lit only by starlight. I have loaded sheet film in light this dark, so don't expect to photograph it or meter it.
Some light meters use a similar scale, but shifted by a constant amount. For instance, the Gossen Luna-Pro uses a scale that reads 5 units higher, or reads 20 in full sun. It's still the same concept, and even those meters calculate the same Exposure Values, or EV, once you set your film speed. That brings us to:
EV, or Exposure Value
Exposure Value, or EV, varies from LV, or Light Value, depending on your film speed.
EV = LV at ISO 100
With ISO/ASA 100 speed film you expose with an Exposure Value (EV) equal to the Light Value (LV).
Easy, eh? Your meter will do this for you, but you can do it in your head, too, if you forget your meter. Here's how:
If you shoot slower film you of course have to use more exposure (EV) for the same Light Value (LV), and vice-versa.
The EV is easy to calculate even if you forgot your meter, since each unit is one stop different than the next. For instance, with film a stop slower than ISO/ASA 100 (like 50 speed Velvia) you just subtract one from the LV to get the EV. This adds one stop of exposure.
For instance, if your subject is at LV14, expose at EV13 with ASA 50 film. EV13 gives one stop more exposure than EV14.
With ISO/ASA 400 speed film you add two to the LV to get the EV, which is the same as subtracting two stops of exposure. Therefore with an LV14 subject you expose at EV16.
Remember that the higher numbers refer to higher light values, and therefore less exposure. This is because the exposure values that correspond to those higher numbers give less exposure.
EVs are a great idea: by talking about an EV you are talking about any one of many different combinations of aperture and shutter speed that give the SAME exposure. Cameras started to use these numbers in the 1950s, but today only the Hasselblad retains them. With every other camera one needs to use the scales on light meters to determine the EV values. Some cameras can be adapted, as I did to my Plaubel Makina 67, which simplifies their use with spot meters.
Zero EV is defined as f/1.0 at one second. Therefore, EV0 is a pretty long exposure. This is the same exposure as f/1.4 at 2 seconds, f/2.0 at 4 seconds, f/2.8 at 8 seconds and so on. EV1 is one stop less: f/1.4 at 1 second. EV 2 is two stops less: f/2.0 at 1 second or equivalent EV is a camera setting. It was popular in the 1950s to couple camera controls together so that once one set an EV one could rotate locked f/stop and shutter speed rings to choose between different equivalent settings. Today only Hasselblad continues the tradition. It is much easier to remember typical light conditions as a single EV number than combinations of camera shutter and aperture settings.
So what's the correct exposure for Velvia (ASA/ISO 50) in side-lit daylight? That light is LV14. Since Velvia is one stop slower than 100 we need to give it one more stop exposure, or SUBTRACT one EV from the LV to get the EV. Therefore, LV14 - 1EV= EV13. EV13 is 1/125 at f/8 or 1/15 at f/22. Light meters that read in EV have scales on the side that show you all the equivalent camera settings for any EV.
What tricks does this tell us? Well, in nature nothing gets brighter than something lit by full sun, which is LV15. If you see LV17 in your meter you know that that must be a white object in daylight. Guess what: that's how evaluative and matrix meters know that, too!
Source : http://www.kenrockwell.com